Hook up subs to stock radio

Added: Noble Acton - Date: 30.08.2021 03:22 - Views: 42172 - Clicks: 2872

Poor sound quality can totally ruin your mood, making you angry without cause. You need the bass effect to improve the sound quality. Unlike the regular subwoofer, a powered subwoofer includes all the components that make up a subwoofer system — the subwoofer, enclosure, and amplifier.

To avoid any form of accidents, it is necessary that you disconnect the negative battery terminal. This way, you protect both you and your vehicle from any hazardous occurrences. For most vehicles, you can run the power cable from the battery through the firewall.

Certainly, it demarcates the main cabin from the engine compartment. When you get inside the cabin, slip the power cable under your vehicle carpet or under trim panels. Try this, until you get to where your powered subwoofer is located — only slip along one side of the carpet. In other cases, the kit has its fuse assembly already assembled and in some cases, it does not. When you have an unassembled fuse, a short piece of the power cable should be cut short, with just enough length to reach the location of the fuse holder from the battery. Mounting the fuse very close to your battery prevents short circuits, as the lead between the fuse and terminal is exposed.

First and foremost, ensure that the turn-on wire and RCA cables are connected to the stereo. Avoid running the turn-on wire and RCA cable right next to the power wire. Run them down the opposite side of the car, away from the power wire. It helps to eradicate the chances of electrical noises entering the system and ruining the sounds produced. You should connect the RCA cables to their respective RCA outputs on the Hook up subs to stock radio while the remote turn-on wire blue wire gets a connection to the wiring harness of the stereo.

This step is only applicable if you have an aftermarket stereo with preamp outputs. Another way to deal with factory stereos is by simply tapping into the speaker wires located right behind your stereo, or the rear deck speakers.

Connect the ground wire to the vehicle chassis using a bolt that you can fasten it with. The terminal of the ground wire must be in contact with the bare metal of the vehicle. To make sure your wire is properly grounded, use sandpaper to sand away paint that can reduce grounding at the point of contact. Connect the power Hook up subs to stock radio to the battery i. The subwoofer also needs to turn on when you start your car, so make sure of that. After all, has been said and done, play your favorite music, set your gains, and get ready for a mind-blowing experience.

To make sure you successfully install your powered subwoofer without causing any damage or accidents, there are certain precautions you need to bear in mind. Here they are. Understanding how to install a powered subwoofer to a factory stereo can sometimes be overwhelming. Remember to keep your subwoofer in good condition by cleaning with a lint-free material over time. To sum up, quality sound is just an installation away. Step 2: Disconnect the battery To avoid any form of accidents, it is necessary that you disconnect the negative battery terminal.

Step 3: Run your amp wire For most vehicles, you can run the power cable from the battery through the firewall. Step 4: Run the turn-on wire and al cables First and foremost, ensure that the turn-on wire and RCA cables are connected to the stereo.

Step 5: Connect the ground wire Connect the ground wire to the vehicle chassis using a bolt that you can fasten it with. Step 6: Handle the wiring connections Connect the power cable to the battery i. Step 7: Get into the music After all, has been said and done, play your favorite music, set your gains, and get ready for a mind-blowing experience. Safety precautions to heed to To make sure you successfully install your powered subwoofer without causing any damage or accidents, there are certain precautions you need to bear in mind.

Be gentle with the wires: Use gentle curves to prevent wear and tear in your wires and cables. Use a capacitor: A capacitor, you will need to prevent a voltage drop when the deep bass hits. Make sure your capacitor is as close to the amp as possible and use the same ground as the one used for the amp. Turn the gain all the way down: During the test-run, turn the gain all the way down and play your music before turning it up to your desired volume. It prevents your powered subwoofer from damaging quickly.

These precautions one should not overlook as accidents are more likely to occur when they are.

Hook up subs to stock radio

email: [email protected] - phone:(128) 940-2401 x 1050

How to Install Subwoofers WITHOUT Replacing Your Stock Stereo